Long Range Rapid Deployment Alert
This is new battery-only version of the Long Range Perimeter Alert systems. The PRO beam-sets are intended for rapid-deployment on construction sites, civil works sites, hazardous sites, large outdoor venues, or any temporary or constantly changing situation.
PRO beam-sets project a powerful detection beam over a distance of more than 260m (this version) allowing intruders or vulnerable people to be detected entering or wandering around on a site before they cause any damage or harm themselves.
Long Range Wireless Battery Powered Perimeter Alert
Battery Powered Wireless Gate Alarm is a high performance wireless Standard Gate Alarm system, this system sounds an alert in your home if a visitor drives or walks through its detection beam. Using a proper photo-electric beam, it makes more immune to false alarms than PIR based systems. Never miss a customer or intruder again. This version has been designed for solar-averse countries or heavily shaded sites.
- Reduce the cost of security guards
- Rechargeable 5000mAh waterproof battery packs (easily swapped)
- Supplied with laser alignment tool
- Beam distance selected by 10-position selector (35-250m range)
- Connect a text messaging (SMS) module to the base receiver to send alert notifications to guard or monitoring company
- Base receiver can drive “police” strobe lights (psychological deterrent)
- Available only in XR-LongRange protocol (long wireless range version)
How the detection beam works …
The image below shows how the projected IR beam has a divergence angle that ensures the receiving beam-unit (called the “Beam-communicator”) is always “seeing the projected spot” unless poorly aligned. Some movement is tolerated because of the beam divergence. In reality the cone-shaped beam does not have a sharply defined boundary – the beam gradually weakens radially outward from the centre until it is too weak to be received.
3 important installation requirements …
(1) Flat ground.
PRO beam-sets work reliably over flat ground. Undulating ground can create detection anomalies where the detection beam is either too high, or too low to the ground.
(2) Rigid Mounting
If the beam-sets are going to be installed in the same location for a long time, we recommend mounting them on a solid fence, wall or on quality hardwood or laminated ply post so they remain aligned indefinitely.
(3) Mounting height
Beam-sets should be mounted between 1000-1200mm above ground (900mm minimum) to minimise “ground scatter”.
| Pro Series Beam Set | |
|---|---|
| Type of Beam | Active Photo-electric Infra-red |
| Maximum Beam distance | 250m |
| Maximum Wireless range | Refer to XR series |
| Diagnostic reports | YES |
| Diameter of IR beam | 65mm |
| Beam alignment method | Laser alignment tool |
| Modulation Type | Gaussian Frequency Shift Keying |
| Radio Frequency | 458.550 MHz |
| RF Output Power | 80-100mW |
| Average Power | 10mW |
| Battery Voltage | 3.7V (charges to 4.2V approx.) |
| Battery Capacity | 5000mAh |
| Protective Metal Housing | Powder-coated stainless steel |
| Weather Resistance |
|
| Dimensions – Millimetres | W80 | D88 | H120 |
| Warranty |
3 Years |
| Base Receiver | |
|---|---|
| Two-way Radio Supervision | YES |
| On-board Diagnostics | YES |
| Maximum Beam-Sets | 4 |
| Volume Adjustment | YES – Adjustable Volume (or muted) |
| Adjustable timed outputs | 4-zone outputs |
| Number of timed outputs | 4 |
| Timed output range | 4 – 120 seconds |
| External Pager output | YES |
| 4G Communicator Port | YES |
| Frequency | 458.550Mhz |
| Power Requirements | 12V DC 500mA |
| Dimensions – Millimetres | W75 | D119 | H30 |
| Warranty | 3 Years |
| By Order | No |
|---|